Cypress SPX-1300 Bedienungsanleitung

SPX-1300_MAN_030513SPX-1300 Cypress Suprex® Reader ExtenderOperations Manual

**Remote UnitSuprex Operation and Initial SetupI/O ControlsCentral Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-L

Suprex Operation and Initial SetupI/O Controls*Central Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1

*Central Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1/Data/F2F Out 1-D0/Clock Out1-D0/CLK Output12-

*Central Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1/Data/F2F Out 1-D0/Clock Out1-D0/CLK Output12-

*Central Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1/Data/F2F Out 1-D0/Clock Out1-D0/CLK Output12-

Input*Central Unit2-8 to 16 VDC In1-Ground8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1/Data/F2F Out 1-D0/Clock Out1-D0/CLK Outp

*Central Unit2-8 to 16 VDC In1-Ground*Remote Unit2-8 to 16 VDC In1-Ground12-RLY2 N.O.11-RLY2 Com10-RLY2 N.C.9-RLY1 N.O.8-RLY1 Com7-RLY1 N.C.6-RS232 Ou

**1K1KI1-I2-I2+I1+2K8 to 16 VDC In GroundRelay 4 N.O.Relay 4 ComRelay 4 N.C.Relay 3 N.O.Relay 3 ComRelay 3 N.C.RS-232 outRS-232 inGround Aux outR2 inR

q `123458rElectrical and Mechanical SpecificationsPhysicalSPX-1300 Aluminum Enclosure 3.5" x 2.75" x .75"SPX-1300 Aluminum Enclosure 3.5

External connections and DIP Switch Settings8-485(+)7-485(-)6-+5 VDC Out5-Prog Res 24-Prog Res 13-LED Input2-D1/Data/F2F Out-1-D0/CLK Out2-8 to 16 VDC

810121416805535-40Ambient Temperature(Degrees Celsius)Supply VoltageTemperature/Voltage de-rating curveElectrical and Environmental SpecificationsThe S

When the Suprex units are operating correctly and have a valid communication channel betweenthe Remote and Central units the Diagnostic indicators on

Suprex Operation and Initial SetupActual connections will differ based on the type of format, features utilized, and equipment interface.The following

*Suprex Operation and Initial Setup2. Remove power from the units and set DIP switches if necessary. The units are set for Wiegand format data as the

**Suprex Operation and Initial SetupCentral Side Basic Panel Connections4. Connect the Central unit to the Access control panel. Power can be supplie

Suprex Operation and Initial SetupCentral Side Basic Panel Connections5. To activate the relay on the Remote unit connect as shown below. These conn