Cypress CapSense CY8C20x36 Betriebsanweisung PDF herunterladen (Seite 72)

72 Document No. 001-64846 Rev. *I Getting Started with CapSense

8. Appendix

8.1 Appendix A: Springs

8.1.1 Finger-Introduced Capacitance

This section gives the influence of various physical parameters on finger-introduced capacitance in a CapSense

design with springs.

 Influence of overlay thickness on Finger Touch added Capacitance (FTC) with springs is similar to that with solid

sensors

Figure 8-1. FTC versus Overlay Thickness

0,2

0,4

0,6

0,8

1,2

0 2 4 6 8 10 12

Thickness of the Overlay, mm

Introduced Capacitance, pF

Spring Solid Sensor

 Influence of height on FTC

Figure 8-2. FTC versus Spring Height

0,1

0,2

0,3

0,4

0,5

0,6

0 5 10 15 20 25 30 35

Height of the Spring, mm

Introduced Capacitance, pF

1 2 ... 67 68 69 70 71 72 73 74 75

Getting Started with CapSense 1
Contents 3
1. Introduction 6
1.4 Document Conventions 9
2. CapSense Technology 10
2.1.2 Mutual-Capacitance 11
2.3.1 Sensing Methods 12
CY8C21x34/B 13
= External Connection 14
2.4 CapSense Tuning 15
2.4.3 Measuring SNR 16
2.4.4.1 What is SmartSense? 17
2.5 Sensor Types 19
2.5.1.2 Matrix Buttons 20
2.5.2.1 Linear Sliders 20
2.5.2.2 Diplexed Sliders 21
Area contacted by finger 22
Proximity Sensor 22
2.6 Sensor Construction 23
2.7.1 Visual Feedback 24
OFFON OFF 26
2.7.2 Haptic Feedback 28
2.7.3 Audible Feedback 29
2.8 Water Tolerance 31
CapSense Controller 32
3. Design Considerations 33
3.2 ESD Protection 34
Non Conductive 35
Material 35
3.2.2 Redirect 36
3.2.3 Clamp 36
3.3.1.1 Ground Plane 37
3.3.1.2 Series Resistor 37
3.3.1.3 Trace Length 37
3.3.1.4 Current Loop Area 37
CapSense 38
Controller 38
3.3.2 Radiated Emissions 39
3.4 Software Filtering 41
3.4.2 IIR Filter 42
Equation 18 43
3.4.3 Median Filter 44
3.4.4 Jitter Filter 45
Unfiltered 46
Filtered 46
3.5 Power Consumption 47
3.6 Pin Assignments 48
3.7 PCB Layout Guidelines 51
3.7.5 Slider Design 52
3.7.8 Trace Routing 53
3.7.9 Crosstalk Solutions 53
3.7.10 Vias 54
3.7.11 Ground Plane 54
Sensor-1 55
Shield Electrode 56
Guard Sensor 56
Sensor Pads 56
4.1.1.1 CY8CMBR20xx 57
4.1.1.2 CY8C201xx 57
4.1.2.1 CY8C20x34, CapSense 57
5. CapSense Selector Guide 59
Design Requirements 60
7. Resources 65
7.4.5 Evaluation Pods 66
7.5 Demonstration Kit 67
7.6 PSoC Designer 67
7.7 PSoC Programmer 68
C-to-USB Bridge Kit 69
7.10 Design Support 71
8. Appendix 72
Introduced Capacitance, pF 73
8.1.4 Design Examples 74

Kommentare zu diesen Handbüchern

Keine Kommentare

Cypress CapSense CY8C20x36 Betriebsanweisung Seite 72

Kommentare zu diesen Handbüchern