Cypress CY62158EV30 Datenblatt Seite 1

MT-X1S ManualJanuary 29, 2015 1 http://www.mattairtech.com/

MT-X1S ManualButtons / JumperThere are four modes of operation which are selected using the PROG button and JMP jumper. The button and jumper are samp

MT-X1S Manualprevents VBUS from rising to the level of the external voltage. Note that there is a minimum load of 100uA for this regulator. The MT-X1S

MT-X1S Manualrouted to a header, to be used for other purposes. External pull resistors are installed to keep the peripheral pins at a defined state d

MT-X1S Manualdisconnected using the solder jumpers. The IC is connected to a 3-pin screw terminal with 3.5mm pin spacing. The pin closest to header F

MT-X1S Manualtemperature is limited to the maximum PCB temperature. It has an accuracy of +/- 2C (max.) and it outputs 19.5mV/C. It consumes only 6uA

MT-X1S ManualWindows InstallationWindows InstallationBefore plugging in the MT-X1S for the first time, the latest software and drivers must be downloa

MT-X1S ManualOnce Atmel Studio is installed, remove jumper JMP and plug in or reset the MT-X1S while holding down the PROG button. This will run the A

MT-X1S ManualMT-X1S Driver / Serial ConfigurationNext, the MT-X1S CDC driver can be installed, which is used by the serial bridge and configuration mo

MT-X1S ManualLinux InstallationLinux InstallationLinux is supported as well. You must download and build the toolchain from the latest script availabl

MT-X1S ManualAVRISP mkII Compatible PDI ProgrammerAVRISP mkII Compatible PDI ProgrammerThe MT-X1S onboard PDI Programmer is based on the AVRISP mkII c

MT-X1S ManualTable of ContentsTable of ContentsOverview...

MT-X1S ManualNext, build the project. Then, click on the Device Programming button. In the Device Programming window, select the AVRISP mkII as the to

MT-X1S ManualNext, select the Memories page. In the Flash section, a hex file can programmed into the targets flash memory. Load your hex file, then

MT-X1S Manual Next, select the Fuses page. It is best to leave the fuse settings alone until you understand what they do. In particular, do not set th

MT-X1S ManualUsing AVRDUDETODO (ie: avrdude -p x128a1 -c avrisp2 -P usb -U flash:w:"myfirmware.hex")January 29, 2015 23 http://www.mattairte

MT-X1S ManualSerial BridgeSerial BridgeThe serial bridge can connect the XMEGA to a host application (ie: terminal emulator) over USB. The XMEGA simpl

MT-X1S ManualBaud Rate Register Value (Manual Speed)Async 1X Async 2X SynchronousUBRR=fosc16∗BAUD−1UBRR=fosc8∗BAUD−1UBRR=fosc2∗BAUD−1BAUD=fosc16∗UBRR

MT-X1S ManualConfigurationConfigurationThe MT-X1S PDI programmer, serial bridge, and other features can be configured by entering configuration mode.

MT-X1S ManualXMEGA Demo ProgramXMEGA Demo ProgramNote: This page describes the preinstalled demo program. This program is primarily meant for testing.

MT-X1S ManualFirmware UpdatesFirmware UpdatesThe MT-X1S firmware will be updated periodically to add new features and fix bugs. These updates will be

MT-X1S ManualFLIP Plug in the MT-X1S with jumper JMP installed and while holding down the PROG button. This will enter the DFU bootloader. LED_STS sho

MT-X1S ManualJanuary 29, 2015 3 http://www.mattairtech.com/

MT-X1S ManualYou may also need to program the EEPROM. If so, click on Select EEPROM at the bottom. Then, click on the File menu and open the appropria

MT-X1S ManualTroubleshooting / FAQTroubleshooting / FAQNothing yetSupport InformationSupport InformationPlease check the MattairTech website (http://w

MT-X1S ManualSchematicSchematicJanuary 29, 2015 32 http://www.mattairtech.com/

MT-X1S ManualLegal NoticesLegal NoticesCopyright NoticesCopyright © 2009-2012, Justin Mattair (http://www.mattairtech.com/)Copyright © 2009-2012, Dean

MT-X1S ManualLicensesLUFA USB LibraryCopyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) Permission to use, copy, modify, distribute,

MT-X1S ManualAppendix A: PrecautionsAppendix A: PrecautionsCAUTIONThe MT-X1S contains static sensitive components.Use the usual ESD procedures when ha

MT-X1S ManualAppendix B: Other MattairTech ProductsAppendix B: Other MattairTech ProductsZeptoProg II AVRISP mkII Programmer●● AVRISPmkII compatible

MT-X1S ManualOverviewOverviewIntroductionThe MT-X1S is a flexible USB development board for the Atmel ATxmega128a1 microcontroller. Included is a Micr

MT-X1S Manual● Audio amplifier connected to XMEGA DAC● Temperature sensor with low-power operation● 1.25V precision voltage reference● Works with XMEG

MT-X1S ManualEight USARTsIrDA modulation/demodulation for one USARTFour 2-Wire Interfaces w/ dual address match (I2C and SMBus)Four SPI (Serial Periph

MT-X1S ManualMT-X1S HardwareMT-X1S HardwareSolder JumpersJumper DescriptionJ1 USB Shield to gnd (not connected by default)J2~5V to relay driver (5V he

MT-X1S ManualJ28 Serial TX (pin E3) to RS-232 DIN or RS-485 DI (external pullup)J29Serial Non-inverting screw-terminal to 680 ohm bias resistor to 3.3

MT-X1S ManualPDI Header PDI header for the XMEGA which can be used for programming or debugging. Note that an onboard programmer is already provided.